Tema: Actualizacnes RIFF-JTAG aqui

RIFF JTAG - Samsung Nexus S, HTC Incredible C Unbrick/Boot repair supported


04.05.2011 HTC Droid Incredible ADR6300 (HTC Incredible C) Unbrick Dead Boot Repair supported




Resurrecting HTC Incredible C is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB3120000′.


To resurrect HTC Incredible C:
Solder JTAG cable to HTC Incredible C JTAG pads;
Insert USB Data cable into board and PC;
Make sure HTC Incredible C is selected in the list of models;
If you use battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume down’ key and press ‘Power ON’ button to enter HBoot menu;
Hold ‘Volume up’ key and press ‘Power ON’ button to enter Recovery mode;



04.05.2011 Samsung Nexus S (i9023) Unbrick Boot repair supported


Samsung I9023 is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
Current resurrector has two different versions of primary boot loaders (PBL) embedded. This depends on hardware version of your phone which boot to use, thus in case of failure (cannot enter download mode after resurrection) of first loader try selecting another.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.


To resurrect Samsung I9023:
Solder JTAG cable to Samsung I9023 JTAG pads;
Connect microUSB cable to phone and PC;
Insert battery;
Make sure Samsung I9023 is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.


To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

[Sólo los usuarios registrados y activos pueden ver los links. ]

[Sólo los usuarios registrados y activos pueden ver los links. ]

by [Sólo los usuarios registrados y activos pueden ver los links. ] on May.07, 2011, under [Sólo los usuarios registrados y activos pueden ver los links. ]
07.05.2011 LG CU720 Shine Unbrick – Boot repair supported
Resurrecting LG CU720 is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
To resurrect LG CU720:

• Solder JTAG cable to LG CU720 JTAG pads;
• Insert USB Data cable into board and PC;
• Make sure LG CU720 is selected in the list of models;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.Đ
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
[Sólo los usuarios registrados y activos pueden ver los links. ]

RIFF JTAG - CDMA LG VM265, CDMA Huawei Broadband Modem EC1260 supported

10.05.2011 CDMA LG VM265, CDMA Huawei Broadband Modem EC1260 supported


Resurrecting LG VM265 is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.


To resurrect LG VM265:

Solder JTAG cable to LG VM265 JTAG pads;
Insert USB Data cable into board and PC;
Make sure LG VM265 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.



Resurrecting Huawei EC1260 is simple. Just make sure you solder all JTAG signals and insert modem into a USB port for it to get powered.
If modem is not detected by RIFFBOX JTAG, disconnect JTAG connector, re-insert modem into USB and then connect back the JTAG connector.
At resurrection startup you can select which zones are to be re-flashed. Thus you can save a lot of time if you know approximately which zone is damaged. Select EFS or MMC areas to be flashed only in case you are sure those are damaged – these areas quite big in size; unnecessary reflash is just a waste of time.
Please note, if you chose EFS to be repaired, an original ESN will be lost and substituted with the one contained in resurrection data. Current resurrector does not support ESN repair.


To resurrect Huawei EC1260:

Solder JTAG cable to Huawei EC1260 JTAG pads;
Insert Huawei EC1260 modem into any USB port for power;
Make sure Huawei EC1260 is selected in the list of models;
Click Resurrect button;
After Selection Dialog popup choose zones to be flashed;
Wait till software signals a successful operation completion;
De-solder JTAG wires;





Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

13.05.2011 RIFF JTAG 16-05-2011 8:29

CDMA Huawei C5589 Unbrick – Boot repair supported
Dopod Magic A6188 (HTC Sapp400) Unbrick, Unlock, IMEI and CID repair supported
Samsung Z630 Unbrick – Boot repair supported

RIFF JTAG - CDMA Updates again
22.06.2011 CDMA day again, 3 new models supported


Whats new:
Motorola W200 full support
Huawei C2801 full support
Nokia 1006 full support
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

ORT - JTAG UPDATE

[29 JUNE 2011]

Description :
Samsung GT-P1000N Unbrick / Repair Dead Boot
Samsung SHW-M130K Unbrick / Repair Dead Boot



Released Stuffs :

Samsung GT-P1000N JTAG Pinout
Samsung GT-P1000N Repair File
Samsung GT-P1000N FULL DUMP
Samsung GT-P1000N Repair Guide
Samsung SHW-M130K JTAG Pinout
Samsung SHW-M130K Repair File
Samsung SHW-M130K FULL DUMP
Samsung SHW-M130K Repair Guide

07.07.2011 HTC Wildfire S A510E (HTC Marvel), More CDMA models supported.

Resurrecting HTC WildFireS is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.01.0002 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC4910000′. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.
To resurrect HTC WildFireS:
Solder JTAG cable to HTC WildFireS JTAG pads;
Insert USB Data cable into board and PC;
Make sure HTC WildFireS is selected in the list of models;
If you use battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button. In few seconds you should see usual android boot mode screen.



Following CDMA models are supported from today :



Samsung B139 Repair/Unbrick, Read/Write NOR Flash
Samsung B259 Repair/Unbrick, Read/Write NOR Flash
Samsung B309 Repair/Unbrick, Read/Write NOR Flash
Samsung B319 Repair/Unbrick, Read/Write NOR Flash
Samsung B379 Repair/Unbrick, Read/Write NOR Flash
Samsung B619 Repair/Unbrick, Read/Write NOR Flash
Huawei C31 Repair, Read/Write NOR flash
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

12.07.2011 Samsung T749, Samsung E189 Unbrick – Boot repair supported


The Samsung T749 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect Samsung T749:
Solder JTAG cable to Samsung T749 JTAG pads;
Connect USB cable;
Make sure Samsung T749 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
In case you cannot find firmware files use Global RIFF Link & Data Exchange plugin – at the moment of resurrector release there was shared full dump from alive Samsung T749 phone.

To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Up’ and ‘Camera’ keys and press ‘Power ON’ button.



Resurrecting Samsung E189 is simple.

Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0×2256

To resurrect Samsung E189:
Solder JTAG cable to Samsung E189 JTAG pads;
Insert USB Data cable into board and PC;
Make sure Samsung E189 is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;



Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

29.07.2011 Samsung GT-i8700 Omnia 7 , Samsung W299 Duos Unbrick – Boot repair supported


Resurrecting Samsung I8700 is simple. Phone is auto powered on with USB Data Cable connected to the PC while battery is inside. In case you use the battery only please note you will have to press Power On key once.

To resurrect Samsung I8700:
Solder JTAG cable to Samsung I8700 JTAG pads;
Make sure Samsung I8700 is selected in the list of models;
Insert Battery into phone and connect USB cable (in case you not use USB cable, press once the Power ON key on the phone)
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Up’ and ‘Camera’ keys and press ‘Power ON’ button. In few seconds phone enters download mode.



Resurrecting Samsung W299 is simple. Phone is auto powered on with USB Data Cable connected to the PC while battery is inside. In case you use the battery only please note you will have to press Power On key once.


To resurrect Samsung W299:
Solder JTAG cable to Samsung W299 JTAG pads;
Make sure Samsung W299 is selected in the list of models;
Insert Battery into phone and connect USB cable (in case you not use USB cable, press once the Power ON key on the phone)
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.




Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

02.08.2011 RIFF JTAG - SonyEricsson Xperia X8, X10 Mini supported

Whats new today :

SonyEricsson Xperia X8/E15 Unbrick, Boot repair, and NAND Chip Backup/Restore
SonnyEricsson Xperia X10a Mini /E10 Unbrick, Boot repair, and NAND Chip Backup/Restore
USB Broadband Modem ZTE MF627 new CPU ID added to allowed list